showpiece/showpiece-pi
1
0
Fork 0
Code Issues Pull Requests Actions Packages Projects Releases 6 Wiki Activity

Switch to new kernel and firmware packages

Browse Source
This commit is contained in:
Serge Schneider
2023-09-07 14:08:13 +01:00
parent 88ac5235d6
commit c856800c72
10 changed files with 53 additions and 64 deletions
Download Patch File Download Diff File Expand all files Collapse all files

17
stage1/00-boot-files/00-run.sh
View File

@@ -1,4 +1,17 @@
#!/bin/bash -e
install -m 644 files/cmdline.txt "${ROOTFS_DIR}/boot/"
install -m 644 files/config.txt "${ROOTFS_DIR}/boot/"
mkdir -p "${ROOTFS_DIR}/boot/firmware"
if ! [ -L "${ROOTFS_DIR}/boot/overlays" ]; then
ln -s firmware/overlays "${ROOTFS_DIR}/boot/overlays"
fi
install -m 644 files/cmdline.txt "${ROOTFS_DIR}/boot/firmware/"
if ! [ -L "${ROOTFS_DIR}/boot/cmdline.txt" ]; then
ln -s firmware/cmdline.txt "${ROOTFS_DIR}/boot/cmdline.txt"
fi
install -m 644 files/config.txt "${ROOTFS_DIR}/boot/firmware/"
if ! [ -L "${ROOTFS_DIR}/boot/config.txt" ]; then
ln -s firmware/config.txt "${ROOTFS_DIR}/boot/config.txt"
fi

62
stage1/00-boot-files/files/config.txt
View File

@@ -1,70 +1,41 @@
# For more options and information see
# http://rpf.io/configtxt
# http://rptl.io/configtxt
# Some settings may impact device functionality. See link above for details
# uncomment if you get no picture on HDMI for a default "safe" mode
#hdmi_safe=1
# uncomment the following to adjust overscan. Use positive numbers if console
# goes off screen, and negative if there is too much border
#overscan_left=16
#overscan_right=16
#overscan_top=16
#overscan_bottom=16
# uncomment to force a console size. By default it will be display's size minus
# overscan.
#framebuffer_width=1280
#framebuffer_height=720
# uncomment if hdmi display is not detected and composite is being output
#hdmi_force_hotplug=1
# uncomment to force a specific HDMI mode (this will force VGA)
#hdmi_group=1
#hdmi_mode=1
# uncomment to force a HDMI mode rather than DVI. This can make audio work in
# DMT (computer monitor) modes
#hdmi_drive=2
# uncomment to increase signal to HDMI, if you have interference, blanking, or
# no display
#config_hdmi_boost=4
# uncomment for composite PAL
#sdtv_mode=2
#uncomment to overclock the arm. 700 MHz is the default.
#arm_freq=800
# Uncomment some or all of these to enable the optional hardware interfaces
#dtparam=i2c_arm=on
#dtparam=i2s=on
#dtparam=spi=on
# Uncomment this to enable infrared communication.
#dtoverlay=gpio-ir,gpio_pin=17
#dtoverlay=gpio-ir-tx,gpio_pin=18
# Additional overlays and parameters are documented /boot/overlays/README
# Enable audio (loads snd_bcm2835)
dtparam=audio=on
# Additional overlays and parameters are documented
# /boot/firmware/overlays/README
# Automatically load overlays for detected cameras
camera_auto_detect=1
# Automatically load overlays for detected DSI displays
display_auto_detect=1
# Automatically load initramfs files, if found
auto_initramfs=1
# Enable DRM VC4 V3D driver
dtoverlay=vc4-kms-v3d
max_framebuffers=2
# Don't have the firmware create an initial video= setting in cmdline.txt.
# Use the kernel's default instead.
disable_fw_kms_setup=1
# Disable compensation for displays with overscan
disable_overscan=1
# Run as fast as firmware / board allows
arm_boost=1
[cm4]
# Enable host mode on the 2711 built-in XHCI USB controller.
# This line should be removed if the legacy DWC2 controller is required
@@ -73,8 +44,3 @@ otg_mode=1
[all]
[pi4]
# Run as fast as firmware / board allows
arm_boost=1
[all]